Tile is usually the first thing chosen for a shower and the last thing questioned. A sample board comes home, a color is picked, and the specification questions get answered by default, in the aisle, without anyone naming them. In the wettest corner of the house, those quiet defaults are the decisions that matter: what the tile is made of decides its upkeep, its size decides whether the floor can drain and the walls can sit flat, and the grout between the pieces decides how the surface looks in five years.
This guide works through the tile specification itself, in the order it should be decided. What sits underneath the tile matters just as much, and our bathroom waterproofing and ventilation checklist covers that layer in full; this post stays on the tile, the format and the grout.
Start with the material, and its real upkeep
The three families on the sample wall behave very differently once water hits them every day.
Porcelain is the benchmark in a shower. By the industry definition, porcelain is tile with a water absorption rate of 0.5% or less, fired dense enough that daily water simply does not get in. It serves on walls and floors alike, takes no sealing, and asks for little beyond ordinary cleaning. When a household wants the shower to be a settled decision, porcelain is usually why.
Ceramic is the lighter-duty relative. It absorbs more water, commonly 3% and above, and its glaze is the working surface that keeps water out of the body. On shower walls, glazed ceramic is a sound and versatile decision. Underfoot inside the shower, where water stands and feet need the tile itself to perform, its softer body and glaze make it the weaker choice.
Natural stone is the honest trade. Marble, travertine, slate and their relatives are porous and vary from piece to piece, which is exactly their beauty. In a shower that porosity has a schedule attached: sealing, commonly every 1 to 2 years, and care with cleaners, because marble and limestone etch when acidic products touch them. Stone is not a mistake in a shower. It is a maintenance commitment, and it should be chosen as one, with eyes open, rather than discovered as one.
The pattern to plan by: the wetter the surface, the more the material's absorption matters. Walls forgive. Floors and constant-spray zones do not.
Match the format to the surface
Tile size is not one decision, because a shower holds two different kinds of surface.
The walls are flat planes, and they accept nearly any format, with one condition that grows with the tile. A tile counts as large format when any edge reaches 15 inches, and large format tightens what the wall beneath it must be: flat within 1/8 inch in 10 feet under the ANSI A108.02 standard, twice the precision smaller tile allows. Long tiles run in a brick pattern add their own rule, offsets held to about a third of the tile length, so edges do not stack into visible steps. Big, calm wall tile is a fine ambition; it simply has to be ordered together with a wall flat enough to carry it.
The floor is not a plane at all. A shower floor slopes about 1/4 inch per foot toward the drain, and it slopes from every direction at once, which makes it a shallow cone. Tile has to bend across that cone, and only small formats can. Mosaic sheets of about 2 inches and under let each piece sit at its own slight angle, following the slope the way a chain follows a curve. A large rigid tile bridges the cone instead: its middle hovers, its low edge holds a line of standing water, and the shower never quite drains or dries.
The small format does a third job while it is down there. Every extra grout line is texture under a wet foot, which leads directly to the next decision.
Choose floor tile by its grip number
Slip resistance is not a vibe; it is a published number. Floor tile is tested for wet dynamic coefficient of friction, DCOF, under the ANSI A326.3 standard, and the figure to know is 0.42: the threshold for level interior floors that are walked on when wet. A shower floor is a harder case than that baseline, constant water and bare feet, and manufacturer guidance for that class, labeled Interior Wet Plus, commonly points higher, around 0.60, in matte or textured finishes.
Three clarifications keep the number honest. First, DCOF is a floor-only figure; it says nothing about wall tile, which never needs it. Second, polished finishes underfoot in a shower work against the number, whatever the tile is made of. Third, no tile is slip-proof: soap film lowers grip, and the slope itself lowers the lab value, which is one more reason the mosaic floor earns its place, its grout lines adding the grip the test cannot promise.
So the floor tile check happens before ordering, on the maker's published data for that exact tile: wet DCOF at or above the level its use class calls for, in a format small enough to follow the floor it will sit on.
Grout is a specification, not an afterthought
Grout fills more than gaps: on a mosaic shower floor it is a large share of the surface your feet meet, and on every surface it is the part that drinks water first. It gets decided in three steps.
Width comes from the tile. The minimum joint is 1/16 inch. Rectified tile, cut to precise size after firing, can run tight joints; tile made to looser tolerances needs wider joints, commonly 3/16 inch or more, so small size differences between pieces disappear into the joint instead of stacking into crooked lines.
Type follows width and surface. Joints narrower than 1/8 inch take unsanded grout; joints of 1/8 inch and wider take sanded grout, whose sand keeps the wider fill from shrinking and cracking. The exception rides along: sanded grout can scratch polished stone and glass, so those surfaces take unsanded grout at any width.
Then the material itself. Standard cement grout is porous; in a shower it needs sealing, and it slowly greys under soap and mineral exposure. Epoxy grout absorbs essentially no water, never needs sealing, and shrugs off that staining, which is why it is the specification so often recommended where water is constant. One last detail separates tidy work from cracked corners: where walls meet the floor and each other, the joint is meant to move, so it is filled with flexible sealant rather than grout, per TCNA movement-joint guidance. Grout packed into a corner is a crack on a schedule.
Tile is the finish of a system
A closing truth that reframes all of the above: no tile, and no grout, is waterproof. The waterproofing is a membrane layer over the structure behind and beneath the tile, and the tile plan answers to it. Format, weight and mortar follow the membrane maker's instructions for the system being built, which is why tile is specified together with that layer and not after it; our waterproofing and ventilation checklist walks through the system itself.
The bathroom floor outside the shower is a separate, drier decision, and our flooring choices by room guide matches materials to rooms there. Inside the shower, the specification chain in this post is the one to settle, and our shower remodeling service page shows how we sequence those choices with the rest of the shower build before anything is ordered.
A simple order to plan in
- Pick the material for each surface by its absorption rate and the upkeep you accept
- Set the wall format, then confirm the wall is flat enough to carry it
- Keep the shower floor to small formats that can follow the slope
- Check the floor tile's published wet DCOF before ordering, not after
- Set joint widths from the tile, then choose sanded, unsanded or epoxy by width and surface
- Confirm the whole tile plan against the waterproofing system's instructions
FAQ
Can we run the big wall tile across the shower floor too?
No, and the reason is geometry, not taste. The floor slopes toward the drain from every direction, and a large rigid tile bridges that slope, holding water and leaving voids beneath it. Floors take small formats, about 2 inches and under in mosaic sheets, which follow the slope piece by piece.
Is porcelain really necessary, or is ceramic fine?
It depends on the surface. Glazed ceramic is a sound choice on shower walls, where its glaze does the work. On the shower floor, porcelain's density (0.5% absorption or less) and harder body make it the reliable default.
Does shower grout need to be sealed?
Cement grout does, on its maker's schedule, because it is porous. Epoxy grout does not; it absorbs essentially no water and never takes a sealer. Either way, the corners where walls meet floor get flexible sealant, not grout, so the joints can move without cracking.
Is natural stone a mistake in a shower?
Not a mistake, a commitment. Stone is porous, needs sealing commonly every 1 to 2 years in a shower, and some stones etch with acidic cleaners. Chosen knowing that, it performs and looks like nothing else. Chosen as if it were porcelain, it disappoints.
